Leading 10 usual forklift accidents ， forklift procedure should pay attention to these issues ！.

Don't underestimate the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight obstructed the driver's sight, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift surrender.
Case 7: The forklift motorist did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these matters ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe prior to starting.
3. When the forklift begins with a load, the vehicle driver ought to initially confirm that the lots is stable and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will cause the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the lots need to not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt way, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance between both forks should be readjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift needs to be braked with the brake. .
4. The speed of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork tip must not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to lift employees to take part in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn Stand-on Electric Pallet Stacker signals are full and efficient.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the automobile;.
2. Stand-on Electric Pallet Stacker When you experience a person in front of you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the automobile ought to be driven in reverse when going downhill;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize braking force to exile round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is raised.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844